Dynex DX-24LD230A12 Bedienungsanleitung PDF herunterladen (Seite 7)

Troubleshooting

DX-24LD230A12

Remote control

General

Disc playback

No output from one

of the speakers

• Adjust the audio balance. See “Adjusting

the sound settings” in the User Guide.

• Make sure that the audio cables are

connected correctly and securely to the

back of your TV/DVD combo.

After images appear • Do not display a still image, such as a logo,

game, or computer image, for an extended

period of time. This can cause a permanent

after-image to be burned into the screen.

This type of damage is not covered by your

warranty.

Problem Solution

Remote control

does not work.

• Make sure that the power cord is correctly

connected to your TV/DVD combo and a

power outlet.

• Make sure that there are no obstructions

between the remote control and the

remote control sensor on the front of the

TV/DVD combo.

• Point the remote control directly at the

remote control sensor on your TV/DVD

combo. For the location of the remote

control sensor, see “Front” in the User

Guide.

• Make sure that the batteries are installed

correctly. See “Installing remote control

batteries” in the User Guide.

• Replace dead batteries with new ones. See

“Installing remote control batteries” in the

User Guide.

Trouble

programming your

existing universal

remote control.

• See instructions and a table of common

codes in “Programming a different universal

remote control” in the User Guide.

• Codes are subject to change. For up to date

codes, go to www.dynexproducts.com.

• Replace dead batteries with new ones. See

“Installing remote control batteries” in the

User Guide.

• Refer to the User Guide that accompanied

your universal remote control and contact

the manufacturer if problems persist.

Problem Solution

No power • Make sure that the power cord is correctly

connected to your TV/DVD combo and a

power outlet.

• Unplug the power cord, wait 60 seconds, then

plug the cord back in and turn on your TV/DVD

combo.

• Other devices (for example, surround sound

receiver, external speakers, fans, or hair dryers)

may be interfering with your TV/DVD combo.

Try turning off one device at a time to

determine which device is causing

interference. Once you have determined

which device is causing interference, move it

further from the TV/DVD combo to eliminate

the interference.

“No signal” error

message is

displayed

•Press INPUT and make sure that you have

selected the correct input for the device or

service you are trying to use.

• If you are using a cable or satellite box, use the

remote that came with that box to change

channels.

Problem Solution

After Auto

Channel Search,

there are no

channels

• Reception can vary by channel depending on

the broadcast power level of a given station.

Contact your cable or satellite TV provider.

• Make sure the antenna or cable/satellite TV is

connected securely to your TV/DVD combo.

• Try replacing the cable between the

antenna/cable or cable/satellite box and your

TV/DVD combo.

One or more

channels do not

display.

• Make sure that the channels are not blocked.

See “Setting parental control levels” in the

User Guide.

• Make sure that the channels are not hidden.

The channel may have been deleted from the

channel list. You can tune to the channel by

pressing the number buttons or you can add

the channel back to the channel list. See

“Hiding channels” in the User Guide.

• If you are using a cable or satellite box, use the

remote that came with that box to change

channels.

• Make sure you have the correct input selected

to view channels from the cable or satellite

box.

• If you are using an antenna, the digital channel

signal may be low. To check the digital channel

signal strength, see “Checking the digital

signal strength” in the User Guide.

Password is lost. • Enter 9999 to access parental controls, then

set a new password. See “Setting or changing

the password” in the User Guide.

Some settings

cannot be

accessed.

• If a setting is grayed, the setting is not

available in the current video input mode.

TV/DVD combo

cabinet creaks.

• When the TV/DVD combo is in use, the

temperature rises naturally and may cause the

cabinet to expand or contract which can cause

a creaking noise. This is not a malfunction.

Control buttons

do not work

• Make sure that the Button Lock option is set

to Off. See “Locking control buttons” in the

User Guide.

• Unplug the power cord, wait a few seconds,

then plug the cord back in and turn on your

TV/DVD combo.

TV/DVD combo

keeps turning off

• Make sure that the sleep timer is not turned

on. See “Setting the sleep timer” in the User

Guide.

Problem Solution

Playback does not

start.

• No disc is loaded. Insert your disc into the

disc slot.

• The disc may be dirty. Clean the disc.

• The disc is not supported. Refer to the User

Guide for a list of compatible disc formats.

No picture. • The TV/DVD combo is not in DVD mode.

Press INPUT and select DVD as the input

source.

No sound. • If an external speaker is connected, check its

volume control.

Picture distortion

during fast

reverse/forward

playback.

• The picture will be distorted occasionally.

This is not a malfunction.

Playback features

failure.

• The playback features such as stopping,

skipping, or repeat play are not applicable to

all discs.

Problem Solution

DX-24LD230A12_11-0728_MAN_IMP INFO.book Page 5 Tuesday, August 16, 2011 7:42 AM

1 2 3 4 5 6 7 8 9 10 11 12

Kommentare zu diesen Handbüchern

Keine Kommentare

Dynex DX-24LD230A12 Bedienungsanleitung Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für LCD-Fernseher Dynex DX-24LD230A12